Getting a smooth, detailed piece out of your silicone mold every time comes down to the right material, the right temperature and the right care. In this guide we walk you step by step through pouring candles, concrete, plaster, stone powder and epoxy in our molds, plus demolding, cleaning and storage.
In short
Our molds are made of silicone in our own workshop. Wax pouring temperatures of 55–95 °C do not strain the mold. Each material, however, has its own temperature, time in the mold and release agent needs.
Use a hard wax for silicone molds: Pillar Soy Wax or paraffin. Container wax and gel wax stick to the mold.
For planters, candle holders and trays. Measure the mortar by the ratio on the bag and apply release agent very thinly.
For scented stones, figurines, incense holders and coasters. Always follow the ratio and timing on the package.
| Material | Pour | Time in mold | Release agent |
|---|---|---|---|
| Pillar Soy Wax | 55–65 °C | Usually 3–5 hours (depending on the mold size) | Not needed |
| Paraffin (+10% stearic) | Pellets ~70 °C, pillar 77–82 °C | Until fully cooled | Not needed |
| Concrete / mortar | Water ratio on the bag | At least 18 hours for regular mortar; a few hours for rapid-set | Water-based, very thin |
| Stone powder / scented stone / plaster | Water ratio on the package | Once set and the heat has passed | Not needed |
| Epoxy resin | A:B ratio on the label | Time on the technical data sheet | If needed, resin-compatible and thin |
Do not pour these into the mold
Molten metal, food and mortars of unknown brand. Test any new material in a single mold first. Our molds are not designed for food.
A few minutes of preparation when your mold arrives sets both the quality of your first pour and the life of the mold.
Before first use, wash the mold in warm soapy water and dry it completely. A drop of water leaves a mark on wax and a void in concrete.
Our Taper Candle M1–M11 and Ghost Taper Candle molds are shipped with a slit; all our other molds come without one. Close a slit mold tightly with rubber bands or packing tape; otherwise material will leak out while you pour.
Place the mold so it stands flat and steady on the counter. If needed, hold it upright with a box or a support.
The plastic inserts (cores) that come with some molds are not heat resistant; do not wash them in hot water or leave them in the sun.
Some designs come out of the mold without a cut; with others, a single cut makes the candle much easier to remove. If you cut, always do it while the mold is empty, before the first pour.
Our Taper Candle Molds M1–M11 and our Ghost Taper Candle Mold are shipped with a cut; don’t cut them, go to step 5. All our other molds arrive uncut. Not every mold needs cutting; it depends on the design and how you use it.
Cut on the back or side of the design, through a thick area. This keeps the front of the candle clean.
With a craft knife or scalpel, start at the pouring opening and follow the lines of the design. A straight cut usually works best.
Craft knifeGently part the cut and check that it reaches the inside of the mold. Then line the edges up exactly.
Before pouring, wrap the mold with rubber bands or packing tape along the whole cut. Material leaks out of a cut that is not closed tightly.
Once the candle has cooled completely, remove the bands or tape, open the cut and peel the mold off the candle.
Place the mold on a flat surface while cutting and always draw the blade away from you.
Where and how to cut your mold, step by step. How to cut a mold
For a smooth candle from a silicone mold, all you need is a hard wax, a thermometer and patience. The steps below are for Pillar Soy Wax; for paraffin, raise the pouring temperature as shown in the table.
Typical temperatures for mold candles: fragrance at 80–85 °C, pouring at 55–65 °C (Pillar Soy Wax) or about 70 °C (paraffin pellets).
Fill the mold with water and weigh the water; the calculator works out the wax your mold holds for you. Set aside 10% extra wax for the second pour. Calculator
Push the hooked wick threading needle in through the wick point at the bottom of the mold, hook the wick and pull it back. The wick now runs through the mold.
Thread the end of the wick through the wooden wick holder and set it on the mold opening; keep the wick taut and right in the center.
Heat the wax in a double boiler or melting pot to 80–85 °C. Do not guess without a thermometer.
Melt the dye in; add the fragrance after taking the wax off the heat and stir gently for 1–2 minutes. For mold candles, 6–8% fragrance is enough.
Pour Pillar Soy Wax at 55–65 °C, slowly, along the side of the mold; if the room is cold, you can go up to 70 °C. Tap the mold gently to release air bubbles.
If the area around the wick sinks as the candle cools, heat the wax you set aside to about 3 °C hotter than the first pour and fill only up to the first pour level.
Leave the candle in the mold to cool; with Pillar Soy Wax, usually after 3–5 hours (depending on the mold size), demold once the mold no longer feels warm and the base is firm. Do not put it in the freezer, the candle will crack. Wait at least 24 hours after pouring before burning.
Demolding is the step that affects the life of your mold the most. Silicone is flexible, but it can tear if thin areas are forced.
The candle should be fully cooled (with Pillar Soy Wax, usually after 3–5 hours, depending on the mold size; it is ready once the mold no longer feels warm and the base is firm); concrete, stone powder and plaster should be fully set and their heat gone. A piece removed too early breaks or loses its shape.
Stretch the mold opening outward with your fingers; once air gets in, the piece starts to release on its own.
Instead of pulling the piece, slowly peel the mold off it. For slit molds, open the slit to remove the piece.
If the candle won't release, put the mold in the fridge for about 5 minutes; the wax shrinks a little more and comes free.
For molds without a slit
If the piece is very hard to remove, you can make a small cut in the side or back of the mold with a craft knife. Close the cut with a rubber band or tape before pouring; it makes demolding noticeably easier.
A clean mold always gives a cleaner surface. Follow these steps after every pour and your mold will stay like new for a long time.
Before washing, wipe the mold with a paper towel to remove leftover material; washing becomes much more effective.
Wash with tap water and a little dish soap. For stubborn residue, soak the mold in soapy water for at least 30 minutes.
Scrub gently with a soft sponge or cloth; stiff brushes and metal scrubbers scratch silicone.
Rinse with plenty of water until no soap remains; leftover soap can mark the surface of your next pour.
Dry with a clean cloth and make sure the inside is completely dry.
High heat and strong detergent permanently damage silicone.
Do not use acetone, paint thinner or similar chemicals; a wet wipe is enough when needed.
Oil-based release agents and petroleum jelly can make silicone swell and soften.
Proper storage extends the life of your mold. One bad habit, on the other hand, can ruin in a few months a mold that would last for years.
Store the mold on a flat surface so it keeps its natural shape; do not fold or bend it.
Stacked molds get crushed and lose their shape; place them side by side.
Do not cram it into a bag and put it in a box, or leave it under heavy items.
Long exposure to sunlight makes silicone yellow and lose its flexibility.
Keep it on a dry shelf, away from very hot or cold places.
Group molds by size and line them up on shelves; they stay protected and you find what you need right away.
Pick your mold or enter the water weight; the calculator works out the wax you need.
The calculator gives you the mortar powder and the mixing water you need.
Why does it happen? Air trapped in the mold during pouring; in concrete, too much water or too much release agent.
How to fix it? For candles, lightly melt the surface with a heat gun or hair dryer. For concrete, fill small voids with fine mortar.
To prevent it Pour slowly along the side and tap the mold gently after pouring; for concrete, vibrate the mold and apply release agent very thinly.
Why does it happen? Using a soft container wax or gel wax; removing the candle before it has fully cooled.
How to fix it? Put the mold in the fridge for about 5 minutes and try again.
To prevent it For molds, use Pillar Soy Wax or add 10% stearic acid to paraffin.
Why does it happen? Wax shrinks as it cools; in thick pieces the area around the wick sinks.
How to fix it? Heat the wax you set aside to about 3 °C hotter than the first pour and fill the hollow up to the first level.
To prevent it Set aside 10% extra wax for pouring and let the candle cool slowly at room temperature.
Why does it happen? Pulling the piece out too early or by a thin area; scraping with a sharp tool.
How to fix it? Small tears usually don't affect the pour; if a tear keeps growing, replace the mold.
To prevent it Peel the mold off the piece and do not force thin areas.
Why does it happen? A slit mold not closed tightly enough, or a wick hole made larger than needed.
How to fix it? Wrap the slit tightly again with a rubber band or tape.
To prevent it Make the wick hole with a thin wick threading needle and use the same hole for every pour.
Pillar Soy Wax is usually poured at 55–65 °C; if the room is cold, you can go up to 70 °C. Paraffin pellets are poured at about 70 °C. These temperatures do not strain the mold, but keep it away from the stove and open flames.
Not for candle wax, plaster or stone powder; silicone releases the piece on its own. For concrete, apply only a water-based release agent in a very thin layer. Oil and petroleum jelly can make silicone swell.
With Pillar Soy Wax, usually 3–5 hours (depending on the mold size); demold once the mold no longer feels warm and the base is firm. Do not leave it in the mold for days; wait at least 24 hours after pouring before burning.
For regular mortars, manufacturers recommend at least 18 hours; rapid-set casting concretes come out in a few hours. Follow the time on the bag and do not leave it in the mold longer than needed once it has set.
No. Wash them by hand with warm soapy water and a soft sponge, then dry completely. The heat and detergent of a dishwasher damage silicone.
Many times, with proper use and storage. Its life depends on what you pour: candle wax doesn't wear the mold, while concrete and epoxy wear fine details faster over time.
Fill the mold with water, weigh the water and enter the grams in the calculator; it works out the wax your mold holds for you.
No. Our molds are designed for candle wax, soap, concrete, plaster, stone powder, scented stone and epoxy; do not use them for food.
We're here to help with anything about your molds and our products. We also make custom silicone molds for your own designs.